CCENT ICND1 Lab Chart

All associated show commands.

A. Basic Switch Router configuration.(try on both)
1.Ping working

2.Console access

3.Hostname

4.Modes
5.Banners

6.Local user name, password, privilege levels, for Console and Telnet access

7.exec-timeout

8.Service Password encryption.(after running this enable password and all get encrypted)

9.Auxilary Password.(connect console cable to auxillary port on router)

10.Loopback interface.

11.Interface description

12.IP address assignment , secondary IP multiple subnets in a LAN
with a single Interface(This Lab needs GNS3 or VIRL as Packet Tracer 
does not support this command),bringing an Interface up.

13.NTP

14.Host name.

15.DNS ip domain lookup , disabling domain lookup

16.Modes

17.Interface types and range

18.Interface specific configuration -speed,duplex,bandwidth,delay,mtu
19.logging synchronous
20.Loopback interface

21.Password ,enable,console,telnet,auxillary

22.Null Interface

23.Passive Interface

24.Clear counters.

B.Medium confgiurations both Switch Router:

1.SSH Configuration

2.Password Reset

3.DHCP : excluded addreses,lease time,configure router interfaces to use DHCP,DHCP helper address.

4.Telnet configuration and Telnet local user database (maybe server)

5.CDP

6.Backing/restoring up Cisco Configuration, copy command.

7.Debugging

Switching:

Management VLAN,IP,Default gateway

Multiple switches , multiple VLAN's – communication only between same VLAN, access ports

Multiple switches Trunk Ports

Layer 3 switch ,different VLAN's,different subnets,ping between them assigning IP to VLAN's

VLAN

Configuring trunk ports and encapsulation

Defining allowed VLAN's on a Trunk Port

Shutdown unused ports

Trunk Port switchport modes

Assign unused ports in unused VLANs

Putting native VLAN in other than VLAN1

InterVLAN

InterVLAN SVI on Layer 3 Switch.
Assigning Static MAC Addresses : mac address-table static

Switch Port Security

-mac-address,sticky,maximum
-violation modes

-Err disable recovery

-Trunking configuration verification DTP,Auto-negotiation

-Verification Troubleshooting

Basic Routing: Static Routing.
Default Routing.
Null Route.

RIP default-information originate


OSPF :
- Basic configuration (wild card masking)
- ip ospf priority
- ip ospf cost
- passive interface (note passive interface is done in router configuration mode )

- passive-interface default (all interfaces to passive)
- subnetted network

-default-information originate

-show commands

ACL - Numbered , Named
- Standard, Extended
- Filtering SSH Telnet
- Wild card Masking
- Editing Named ACL's
- log,log-input,established,remark

- ACL applied to InterVLAN interfaces.

-show commands

NAT - Static
- Dynamic

- PAT (using a Pool and Interface)
- Using a Static or default route to reach a static NAT global IP
(Lab for Dynamic NAT or PAT also)
- Using a Null route and OSPF redistribute static command
to advertise a NAT Global IP Subnet.
(Lab for Dynamic NAT or PAT also)

- show commands
IPv6 - IPv6 Address assignments different types methods.

-Ipv6 enable

-Manual full IP

-Global IP Manual EUI-64

-Link local manually assigned

-try all link local,unique local,global

-using Autoconfig --ipv6 address autoconfig

- IPv6 address auto assignment to Host(computer) from Router.
- Stateless Autoconfiguration EUI-64 :MAC changed to IPv6
- OSPFv3 , router-id
- Static Routing using link local,unique local and global

- Ipv6 default route

- show commands

Ping , Extended Ping, Runts, Giants,Traceroute
debug command
Show commands all
Troubleshooting scenarios.Multiple protocol configurations.